Inland 0.47µF-1000µF Electrolytic Capacitor Assortment Kit (13 Values, 200pcs)
Overview
A single-category assortment card of radial electrolytic capacitors, 13 values spanning 0.47µF to 1000µF. Same Inland/Micro Center house brand already in the library via the QAPASS/inland 16x2 LCD backpack — a different product line, same reseller brand. Complements the 1400pcs generic electronic components kit already logged, which only carries 12 electrolytic values up to 470µF at a single 50V rating — this kit adds higher-capacitance/lower-voltage options (680µF, 1000µF at 25–35V) not covered there.
Key specs
Full breakdown as printed on the card (all 13 values sum to the card’s stated 200pcs):
| Value | Voltage | Qty |
|---|---|---|
| 0.47µF | 50V | 20 |
| 1µF | 50V | 20 |
| 2.2µF | 50V | 20 |
| 4.7µF | 50V | 20 |
| 10µF | 50V | 20 |
| 22µF | 50V | 20 |
| 33µF | 35V | 20 |
| 47µF | 25V | 20 |
| 100µF | 35V | 10 |
| 220µF | 25V | 10 |
| 470µF | 25V | 10 |
| 680µF | 25V | 5 |
| 1000µF | 35V | 5 |
- Package: radial leaded, through-hole
- Voltage ratings vary by value (25V/35V/50V depending on capacitance) — not a single shared voltage rating across the kit
- Card carries a California Prop 65 warning (cancer/reproductive harm, standard for electrolytic capacitor chemistry) — no unique hazard beyond typical for this component class
Pinout
| Lead | Function |
|---|---|
| Longer lead | + (anode) |
| Shorter lead, stripe-marked side of can | − (cathode) |
Standard radial electrolytic polarity marking — reversing it can vent/rupture the capacitor. Verify against the physical part’s own stripe marking before wiring, not just this table.
Wiring / typical usage
General-purpose bulk/decoupling/filtering stock: reservoir capacitors on power rails, bulk filtering after a rectifier or boost/buck converter, or low-frequency coupling. Higher-value units here (470–1000µF) are suited to power-supply smoothing; lower values (0.47–10µF) suit general filtering roles. Always respect the printed voltage rating for the specific value pulled — mixing up which value/voltage pair is in hand risks under-rating a capacitor for its circuit.
Code / libraries
N/A — passive component, no firmware library involved.
Source material
- Full spec table (values, voltages, quantities) transcribed directly from the card’s own printed label — high confidence, all quantities cross-checked and summed to exactly the card’s stated 200pcs across 13 values.
- Product photo:
/inventory/inland-electrolytic-capacitor-kit-200pcs/product-photo.jpeg— photo of the card’s own label, which doubles as the spec sheet.
Verification
Read directly from the card's own printed label (photo-verified) — high confidence for values/voltages/quantities as advertised. Individual units not measured/tested against their printed ratings.
Notes / gotchas
- Don’t confuse this with the 1400pcs generic kit’s electrolytic section — different value sets, different voltage ratings per value, and this kit’s higher-capacitance values (680µF/1000µF) aren’t present there at all.
- Voltage rating is not uniform across the kit — a 1000µF cap here is rated 35V while a 47µF cap is rated only 25V; check the specific value’s own rating before assuming a blanket voltage headroom.
- Radial electrolytics are polarized — always confirm the stripe/short-lead cathode side before inserting into a circuit.